HORIZON FACEPLATE, 2-GANG, WHITE [LIMITED SUPPLY] - 6509709

0-10V HEATING/COOLING FAN-COIL THERMOSTAT, WHITE TEXTURED - 6508012 Audio & Video

0-10V HEATING/COOLING FAN-COIL THERMOSTAT, WHITE TEXTURED - 6508012

HEATING/COOLING FAN-COIL THERMOSTAT, ALMOND - 6508010 Audio & Video

HEATING/COOLING FAN-COIL THERMOSTAT, ALMOND - 6508010

Xiaomi TV A Pro 55'' 139.7 cm (55 ) 4K Ultra HD Smart TV Wi-Fi Grey Titanium Audio & Video

Xiaomi Smart Projector L1 120 Android TV Full HD Audio & Video

4352 Audio & Video

Xiaomi | Mi Selfie Stick Tripod | Aluminium | Black | Non-slip construction; Rotation angle: 360°; Portable and Wireless Audio & Video

Crestron FT2A-CBLR-BRKT-1200 cable gender changer Audio & Video

The FT2A-CBLR-BRKT-1200 is an adapter bracket for a Crestron FT2-1200 Series FlipTop that enables the installation of two cable retractors in the middle positions within the FlipTop. It attaches to the front or rear of the FlipTop chassis beneath the table, and provides mounting slots for two retractors and one power supply.FT2-1200 Series FlipTops normally support the installation of cable retractors at the left and right ends of the module row. Adding the FT2A-CBLR-BRKT-1200 bracket allows retractors to be installed in the middle of the row, allowing for a total of up to four retractors across the entire row. One mid-row retractor occupies the third and fourth module slots, while the other occupies the sixth and seventh slots. A single module space remains at the center of the row (fifth slot) to accommodate any single-space module or blank plate.When installing mid-row retractors, the bracket and retractors can attach to either the front or rear of the FlipTop chassis below the table. When installed, the mid-row retractor enclosures project from the front or rear of the chassis perpendicular to the end-mounted retractors. The cable connectors nest within the retractor modules above the table at a 90° rotation relative to other connectors within the FlipTop.Note: Using the bracket, an FT2A-CBLR-GR Series Gravity Retractor requires 2-3/4 inches (70 mm) horizontal clearance, and an FT2A-CBLR-1T Series One-Touch Retractor requires 9 inches (228 mm) horizontal clearance, measured from the front or rear of the FlipTop chassis beneath the table. Refer to each product's spec sheet for additional dimensions and clearances.When used with an FT2-1200-ELEC Series "Electrical" FlipTop, the FT2A-CBLR-BRKT-1200 bracket retains the ability to mount a single FT2A-UTK-PWS power supply on the same side as the cable retractor.

Crestron FT2A-CBL-PT-VGA VGA cable Audio & Video

Crestron Pass-Through Cables (FT2A-CBL-PT Series) offer a cost-effective cable management solution for use with Crestron FT2 Series FlipTop cable management systems. Each cable installs in the FlipTop using a cable pass-through plate module , which allows the cable to be pulled out smoothly for use, and then dropped back into the FlipTop when done. When stowed in the FlipTop, the cable simply drops beneath the table while the connector remains neatly nested in the pass-through plate.Crestron pass-through cables feature a highly flexible, low-friction design using flat construction and durable dual-layer jacket. The connector ends are sculpted with a  soft-feel boot for easy handling and uniform alignment within the FlipTop.The following 4K pass-through cables feature a minimum TMDS bandwidth of 18 Gbps to support ultra high-definition digital video signals up to 4K60 4:4:4. Active circuitry is employed for optimal performance.Additional pass-through cables are available to support analog AV and data signals. These cables are passive.The FT2A-CBL-PT Series pass-through cables are suitable for use as a repair replacement for Crestron FT2A-CBLR-GR series cable retractors.

Activejet AJE-BLANKA 3P ceiling lamp Audio & Video

Activejet GIZEL double ceiling wall light strip chrome E14 wall lamp for living room Audio & Video